Toyota Center-Controlled Rider Pallet Jack
| The Toyota Industrial Equipment Center-Controlled Rider Pallet Jack is easy to maneuver and quick to respond to commands. The motorized pallet jack, ideal for longer runs, provides a comfortable operator compartment. Doubling as a ground-level order picker, the Center-Controlled Rider Pallet Jack is an asset to any warehouse or distribution center. |
LARGE IC CUSHION FORKLIFT
|
Model
|
Load Capacity (lbs.)
|
Max Travel Speed Full Load (MPH)
|
Max Gradeability Full Load (%)
|
Basic Right Angle Stack (in.)
|
|
8HBC30
|
6,000 on level surfaces
|
6.5
|
10
|
98.8
|
|
8HBC40
|
7,000 on level surfaces
|
5
|
10
|
142
|
PERFORMANCE
- AC drive motor with thermal protection & current limiting
- 24-Volt electrical system
- 6" lift
- Programmable performance
- Adjustable maximum speed
- Adjustable acceleration
- Fault code memory with hour meter reading
- Regenerative braking
- On/off key switch
- Lift limit switch
- Multiple hour meter indicator
- Battery discharge indicator with lift interrupt
- Fused control & power circuits
- Hydraulic overload protection valve
- Dual 1.25"-dia. lift cylinders
- Polyurethane torsion block stabilizing casters1
- Heavy-duty spring-loaded stabilizing casters2
- 31.5"-long x 13.44"-wide battery compartment3
- SB-175 battery connector (gray) &Cold storage conditioning
- Multifunction control handle with ergonomically angled handgrips &
wrap-around hand guard - Dual thumbwheels with twist grips for directional control & travel speed
- Intuitively positioned lift/lower buttons
- Adjustable height control handle (3-position); dual hand brake levers
- Low-eff ort control handle
- High-speed interlock button
- Bubble-cushioned operator floor mat, padded backrest & knee pad
- Walk-through operator compartment
- Low platform step height
- Control Area Network (CAN-bus) communications
- Welded construction with reinforced heavy-duty bumper
- Powder coat paint finish
- Box rail fork construction
- Steel bulkhead wrappers
- Forged rectangular steel tension rods
- Heavy-duty bushings & pins
- Solid trail fork casting
- Tapered fork tips with pallet entry slides
- Four-point lift linkage
- High-strength polymer service cover
- Rubber drive tire
- Hall-effect switches
- 48" load backrest extension
- AC drive motor (no brushes or commutator)
- Self-adjusting electric disc brake
- One-piece, lightweight service access cover
- Error indicator with self-diagnostics
- Tefl on®-coated Polylube™ lift linkage bushings (maintenance free)
- Wrap-around hand guard • Control handle with dual brake levers • Electronic horn
- 48," 60" and 72" load backrest extension
- Electronic travel alarm (forward & reverse)
- Controller splash guard1
- Keyless on/off switch2
- Power hookup for onboard terminal (24-Volt, 2 amp)3
- Power hookup for onboard terminal (24-Volt, 10 amp)3
- Storage tray with clipboard, battery compartment mounted8
- Pallet entry/exit rollers (single length pallet forks only 36"– 60")
- Steel bumper skirt (2.25" underclearance)
- Turtle speed (3-position key switch)
- Jog buttons with turtle speed (3-position key switch)
- Dual stretch wrap holder, load backrest mounted
- Lubrication package for pivot points (grease fittings)
- Steering bearing, greaseable
- 6" extended operator compartment
- Battery compartment rollers with dual side gates 4
- Battery side gate interlock switches5
- 32"-high battery retaining wall6
- Battery spacer kit
- Polyurethane drive tire
- Non-marking rubber drive tire
- Heavy-duty load wheels (Vulkollan®)10
- Heavy-duty spring-loaded stabilizing casters
- Load wheel debris diversion device13
- Polyurethane load wheels (tan durometer 95)10
- Load wheels, single axle/dual 10
- Load wheels, single axle/triple 10
- Power steering 16
- Cold storage conditioning 14-15
- Special paint color, complete truck
- UL-approved model type “E”11
- UL-approved model type “EE”12
- Factory pre-programmed maximum travel speed of 5 mph
Model:8HBC40, Wheel Type: Rubber / Polyurethane
Fuel Type: Battery, Electrical System Voltage: 24V